Motorola MC3000 Dokumentacja Strona 109

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
Przeglądanie stron 108
Wireless Applications 7 - 7
Tap Next. If Ad-Hoc mode was selected the Ad-Hoc dialog box displays. If Infrastructure mode was selected the
Authentication dialog box displays. See Authentication on page 7-8 for instruction on setting up authentication.
Table 7-5
Operating Mode Fields
Field Description
Operating
Mode
Infrastructure: Select
Infrastructure
to enable the mobile computer to transmit and receive data
with an AP. Infrastructure is the mobile computer default mode.
Ad Hoc: Select
Ad Hoc
to enable the mobile computer to form its own local network where mobile
computers communicate peer-to-peer without APs using a shared ESSID.
Country Country: is used to determine if the profile is valid for the country of operation. The profile country
must match the country in the options. page or it must match the acquired country if 802.11d is
enabled.
Single Country Use:
When the device is only to be used in a single country, set every profile country to
Allow Any
Country
. In the
Options
>
Regulatory
dialog box (see
Figure 7-44 on page 7-37
), set the country
to the specific country the device is to be used in, and deselect (uncheck) the Enable 802.11d
option. This is the most common and the efficient configuration. It eliminates the initialization
overhead associated with acquiring a country via 802.11d.
Multiple Country Use:
When the device may be used in more than one country, select (check) the Enable 802.11d
option in the
Regulatory Options
dialog box (see
Figure 7-44 on page 7-37
). This eliminates the
need for reprograming the country (in
Options
>
Regulatory
) each time a new country is entered.
However, this only works if the infrastructure (i.e. APs) support 802.11d (some infrastructures do
not support 802.11d, including some Cisco APs). When the Enable 802.11d option is selected,
the
Options
>
Regulatory
>
Country
setting is not used. For a single profile that can be used in
multiple countries, with infrastructure that supports 802.11d (including Symbol infrastructure), set
the Profile Country to
Allow Any Country
. Under
Options
>
Regulatory
, select
Enable 802.11d
.
The
Options
>
Regulatory
>
Country
setting is not used.
For a single profile that can be used in multiple countries, but with infrastructure that does not
support 802.11d, set the profile country to
Allow Any Country
, and de-select (uncheck)
Enable
802.11d
. In this case, the
Options
>
Regulatory
>
Country
setting must always be set to the
country the device is currently in. This configuration option is the most efficient and may be
chosen for use with any infrastructure. However, the
Options
>
Regulatory
>
Country
setting must
be manually changed when a new country is entered.
Note that using a single profile in multiple countries implies that there is a common ESSID to
connect to in each country. This is less likely than having unique ESSIDs in each country, this
requires unique profiles for each country.
For additional efficiency when using multiple profiles that can be used in multiple countries, the
country setting for each profile can be set to a specific country. If the current country (found via
802.11d or set by
Options
>
Regulatory
>
Country
when 802.11d is disabled) does not match the
country set in a given profile, then that profile is disabled. This can make profile roaming occur
faster. For example, if two profiles are created and configured for Japan, and two more profiles
are created and configured for USA, then when in Japan only the first two profiles are active, and
when in USA only the last two are active. If they had all been configured for
Allow Any Country
,
then all four would always be active, making profile roaming less efficient.
Przeglądanie stron 108
1 2 ... 104 105 106 107 108 109 110 111 112 113 114 ... 215 216

Komentarze do niniejszej Instrukcji

Brak uwag